新聞中心
NEWS CENTER
聯系我們
CONTACTS US
濟南皓暉建材有限公司，總部位于中國泉城——山東濟南，是一家專業生產銷售石塑電梯門套，仿大理石電梯門套的專業廠家。皓暉建材在電梯門套生產行業很多年，憑著優質的產品質量和完善的售后服務，在全國各地都有我們的工程案例。
我們本著“以質量求生存 ，靠管理出效益，憑信譽贏口碑,以實干筑輝煌”的經營理念，公司將立足于當代建材現代化發展前沿，依靠科技、勇于探索，以優質產品優良服務、信譽與廣大用戶攜手共創輝煌。
聯系電話： 15853163650
工廠地址：山東濟南章丘區（歡迎廣大客戶來廠勘察）
公司動態
COMPANY NEWS
電梯門套的房門部分施工方法
2017-02-24 17:29:41 文章來源：www.leo918.cn
電梯門套的房門部分施工方法：
The door part of the construction method of elevator door:
1、空心門做法：門扇厚度為43-45mm。用12mm夾板開條，四周立放2-3圈，加固橫條間距不能超過200mm，裝鎖位置不能留空，合頁位必須加固，兩面封5mm夾板，再封飾面。
1, hollow door door leaf thickness 43-45mm approach. 12mm plywood for open, around vertical circle 2-3, reinforcement bar spacing of not more than 200mm, to hold the lock location cannot be blank, a hinge must be strengthened, both sides seal 5mm splint, and then seal finishes.
2、實心門做法：門扇厚度為43-45mm的，用進口夾板平壓，夾板雙面開出對稱的平衡縫，夾板間用白乳膠有用槍釘固牢，如果需要粉刷大面積墻面，建議使用不銹鋼電梯裝飾板。空心門放于標準的壓床平壓4天以上，不銹鋼電梯門套施工每道工序都必須涂上白乳膠；實心門做好后必須再貼面板，放于標準床平壓4天以上。
2, the solid door practices: door leaf thickness 43-45mm, pressed plywood imports, splint double-sided opened symmetrical balance seam, splints with white latex useful gun nail fastened, if need to paint the wall in a large area, it is recommended the use of stainless steel decorative plate for lift. Hollow door put in standard press flat pressure for more than 4 days, stainless steel elevator door construction each process must coat with white latex; good solid doors must stick panel again, put to the standard flat bed press for more than 4 days.
本文由電梯門套友情奉獻。更多有關的知識請點擊：http://www.leo918.cn>最真誠的態度。為您提供最為全面的服務。更多有關的知識我們將會陸續向大家奉獻。敬請期待。
This article is contributed by the elevator door friendship. More knowledge about please click: attitude of http://www.leo918.cn most sincere. For you to provide the most comprehensive services. More relevant knowledge and we will continue to everyone dedication. Stay tuned.
The door part of the construction method of elevator door:
1、空心門做法：門扇厚度為43-45mm。用12mm夾板開條，四周立放2-3圈，加固橫條間距不能超過200mm，裝鎖位置不能留空，合頁位必須加固，兩面封5mm夾板，再封飾面。
1, hollow door door leaf thickness 43-45mm approach. 12mm plywood for open, around vertical circle 2-3, reinforcement bar spacing of not more than 200mm, to hold the lock location cannot be blank, a hinge must be strengthened, both sides seal 5mm splint, and then seal finishes.
2、實心門做法：門扇厚度為43-45mm的，用進口夾板平壓，夾板雙面開出對稱的平衡縫，夾板間用白乳膠有用槍釘固牢，如果需要粉刷大面積墻面，建議使用不銹鋼電梯裝飾板。空心門放于標準的壓床平壓4天以上，不銹鋼電梯門套施工每道工序都必須涂上白乳膠；實心門做好后必須再貼面板，放于標準床平壓4天以上。
2, the solid door practices: door leaf thickness 43-45mm, pressed plywood imports, splint double-sided opened symmetrical balance seam, splints with white latex useful gun nail fastened, if need to paint the wall in a large area, it is recommended the use of stainless steel decorative plate for lift. Hollow door put in standard press flat pressure for more than 4 days, stainless steel elevator door construction each process must coat with white latex; good solid doors must stick panel again, put to the standard flat bed press for more than 4 days.
本文由電梯門套友情奉獻。更多有關的知識請點擊：http://www.leo918.cn>最真誠的態度。為您提供最為全面的服務。更多有關的知識我們將會陸續向大家奉獻。敬請期待。
This article is contributed by the elevator door friendship. More knowledge about please click: attitude of http://www.leo918.cn most sincere. For you to provide the most comprehensive services. More relevant knowledge and we will continue to everyone dedication. Stay tuned.
上一篇：仿大理石uv板的防水性能
下一篇：KTV搬回家的的5大理由
