新聞中心
NEWS CENTER
聯系我們
CONTACTS US
濟南皓暉建材有限公司，總部位于中國泉城——山東濟南，是一家專業生產銷售石塑電梯門套，仿大理石電梯門套的專業廠家。皓暉建材在電梯門套生產行業很多年，憑著優質的產品質量和完善的售后服務，在全國各地都有我們的工程案例。
我們本著“以質量求生存 ，靠管理出效益，憑信譽贏口碑,以實干筑輝煌”的經營理念，公司將立足于當代建材現代化發展前沿，依靠科技、勇于探索，以優質產品優良服務、信譽與廣大用戶攜手共創輝煌。
聯系電話： 15853163650
工廠地址：山東濟南章丘區（歡迎廣大客戶來廠勘察）
公司動態
COMPANY NEWS
石塑UV板翻新的流程
2016-03-25 16:48:49 文章來源：www.leo918.cn
石塑UV板翻新打磨前先勾縫，然后做防水，再做填縫，目的是使到石塑UV板盡可能少吸水，達到降低石塑UV板吸水律，條件允許的情況下最后再做一次防水。
Coarse grinding: grinding stone plastic UV board in the first groove seam water again, then filling. After the waterproof effect, using diamond resin abrasive block, coarse grinding to water remember not too much, each grinding mill finish mop clean, to completely drain the water, check the shear mouth grinding leave deep scratch if slices 50# wear off and, by analogy, the machine shaft grinding, coarse grinding accounted for the overall grinding 45% of the time, is to ensure the completion of the project, the key link of the quality acceptance.
細磨：后研磨前先再做防水，等防水效果出來后，使用金鋼石樹脂軟水磨片，細磨占整體研35%時間，細磨到2000#后光澤度可達50度。
Fine grinding: grinding before doing waterproof, waterproof effect, using diamond resin soft grinding, fine grinding accounted for the overall development of 35% of the time, fine grinding to 2000# backlight Ze of up to 50 degrees.
精磨：研磨前石塑UV板必須有70%的干燥，先用石塑UV板填封劑作前處理，使到石塑UV板在填補疏松同時也強化了材質。精磨后光澤度提升很高，石塑UV板表面密度提高了，為拋光劑打下堅實的基礎，增強了拋光材料的附著力。
Grinding: grinding stone plastic UV board must be 70% dry, first stone plastic UV board filling and sealing agent for pretreatment, to the stone plastic UV board in fills the loose and also to strengthen the material. After polishing, the gloss is improved very high, and the surface density of UV plate is improved, which is the base of polishing agent, and the adhesion of polishing material is enhanced.
拋光：拋光石塑UV板必須是徹底干燥的，使用晶面機功率2HP以上，導入乳Q5進行拋光研磨，拋光后石塑UV板表面光澤度可達最少，90-100度以上。
Polishing, polishing stone plastic UV board must is completely dry, use crystal face power 2HP above, import milk Q5 for grinding and polishing, polishing Houshi plastic boards UV gloss surface can reach at least, 90-100 degrees above.
本文由仿大理石線條友情為您提供，更多的精彩內容請點擊：http://haohui.winbrand.cc歡迎您的訪問。
In this article, we will provide you with the imitation of marble lines. Please click: http://haohui.winbrand.cc welcome your visit.
Stone plastic UV board reconditioned and polished before pointing first, then do waterproofing, sealing to make to the stone plastic UV board as far as possible to reduce water absorption, to reduce the stone plastic UV absorbent plate law, the allowable conditions finally do a waterproof.
Coarse grinding: grinding stone plastic UV board in the first groove seam water again, then filling. After the waterproof effect, using diamond resin abrasive block, coarse grinding to water remember not too much, each grinding mill finish mop clean, to completely drain the water, check the shear mouth grinding leave deep scratch if slices 50# wear off and, by analogy, the machine shaft grinding, coarse grinding accounted for the overall grinding 45% of the time, is to ensure the completion of the project, the key link of the quality acceptance.
細磨：后研磨前先再做防水，等防水效果出來后，使用金鋼石樹脂軟水磨片，細磨占整體研35%時間，細磨到2000#后光澤度可達50度。
Fine grinding: grinding before doing waterproof, waterproof effect, using diamond resin soft grinding, fine grinding accounted for the overall development of 35% of the time, fine grinding to 2000# backlight Ze of up to 50 degrees.
精磨：研磨前石塑UV板必須有70%的干燥，先用石塑UV板填封劑作前處理，使到石塑UV板在填補疏松同時也強化了材質。精磨后光澤度提升很高，石塑UV板表面密度提高了，為拋光劑打下堅實的基礎，增強了拋光材料的附著力。
Grinding: grinding stone plastic UV board must be 70% dry, first stone plastic UV board filling and sealing agent for pretreatment, to the stone plastic UV board in fills the loose and also to strengthen the material. After polishing, the gloss is improved very high, and the surface density of UV plate is improved, which is the base of polishing agent, and the adhesion of polishing material is enhanced.
拋光：拋光石塑UV板必須是徹底干燥的，使用晶面機功率2HP以上，導入乳Q5進行拋光研磨，拋光后石塑UV板表面光澤度可達最少，90-100度以上。
Polishing, polishing stone plastic UV board must is completely dry, use crystal face power 2HP above, import milk Q5 for grinding and polishing, polishing Houshi plastic boards UV gloss surface can reach at least, 90-100 degrees above.
本文由仿大理石線條友情為您提供，更多的精彩內容請點擊：http://haohui.winbrand.cc歡迎您的訪問。
In this article, we will provide you with the imitation of marble lines. Please click: http://haohui.winbrand.cc welcome your visit.
上一篇：預防大理石水斑病變的方法
下一篇：保護地球資源呼吁新型建材
